HYDRAULIC INJECTION MOLDING MACHINE SPECIFICATIONS
CLAMP UNIT	UNITS	MODEL ISGS610				MODEL ISGS610-WP
CLAMP CLOSING FORCE	tons-US	605				605
	tons-m	550				550
CLAMP OPENING FORCE	tons-US	33				33
	tons-m	30				30
TIE BAR SPACING (H x V)	in	33.8 x 33.8				38 x 38
	mm	860 x 860				965 x 965
PLATEN DIMENSION (H x V)	in	48.4 x 48.4				55.1 x 55.1
	mm	1230 x 1230				1400 x 1400
CLAMP STROKE	in	47				47
	mm	1200				1200
DAYLIGHT (OPEN/CLOSE)	in	63 / 15.8				63 / 15.8
	mm	1600 / 400				1600 / 400
CLAMP SPEED (CLOSE/OPEN)	in/sec	31 / 30				31 / 30
	mm/sec	800 / 760				800 / 760
EJECTOR FORCE	tons-US	16				16
	tons- m	14.5				14.5
EJECTOR STROKE	in	6.3				6.3
	mm	160				160
INJECTION UNIT		34AT	34B	59AT	59B	34AT	34B	59AT	59B
INJECTION CAPACITY (GPPS)	oz	61	77	104	126	104	126	104	126
	g	1730	2190	2900	3540	2900	3540	2900	3540
SCREW DIAMETER	in	3.2	3.5	3.7	4.1	3.7	4.1	3.7	4.1
	mm	80	90	95	105	95	105	95	105
INJECTION VOLUME	in3	115	145	192	235	192	235	192	235
	cm3	1880	2380	3150	3850	3150	3850	3150	3850
INJECTION PRESSURE	PSI	26500	21000	26800	21900	26800	21900	26800	21900
	kgf/cm2	1860	1470	1890	1540	1890	1540	1890	1540
INJECTION RATE	in3/sec	39	49	38	47	39	49	38	47
	cm3/sec	635	800	625	765	635	800	625	765
MAX SCREW SPEED	RPM	170	150	140	127	140	150	140	127
	RPM	170	150	140	127	140	150	140	127
PLASTICIZING RATE (GPPS)	oz/sec	3.3	3.9	4.2	4.9	4.2	4.9	4.2	4.9
	g/sec	95	111	117	136	117	136	117	136
GENERAL DATA
*CORE VOLUME CLAMP STOP	gpm	57				57
	L	215				215
*CORE VOLUME ON THE FLY	gpm	19				19
	L	72				72
RUNNING LOAD @ 460V	amps	163 & 179				163 & 179
	amps	163 & 179				163 & 179
COOLING WATER REQUIRED	gal	13				13
	L	49				49
MOTOR	HP	100				100
	kw	74				74
OIL RESERVOIR CAPACITY	gal	450				450
	l	1700				1700
SHIPPING WEIGHT (EST.)	Lbs	57,200		59,400		59,400		61,600
	kg	26,000		27,000		27,000		28,000
DIMENSIONS (L x W x H)	ft	26.6x7.2x6.9		28.6x7.2x6.9		26.6x7.5x6.9		28.6x7.5x6.9
	m	8.1x2.2x2.1		8.7x2.2x2.1		8.1x2.3x2.1		8.7x2.3x2.1