ISF SERIES
INJECTION MOLDING MACHINES

Standard Features

     INJECTVISOR V21 ultra high speed computer control with: 

  • Active Matrix full-color LCD screen with direct input touch control.
  • Bilingual capability (English/Spanish).
  • Numerical closed loop control of injection speeds and pressures.
  • 12 speeds and 6 pressures for profile injection control.
  • Adjustable injection speed and hold pressure gradient ramp or point to pointprogressive profile capability for smooth speed transition.
  • Injection speed and pressure set point graph with real time overlay.
  • Automatic screw speed deceleration and screw back pressure reduction for accurate screw stopping after recovery.
  • Transfer from injection speed to pressure by position or hydraulic pressure (cavity pressure optional).
  • Digital setting of screw back pressure.
  • Screw back pressure programmable with set point graph and actual graph.
  • Screw speed programmable with set point and actual graph.
  • Digital display of injection pressure and clamp force.
  • Digital display of screw speed.
  • Digital setting of clamp open and close speeds and positions.
  • Clamp open and close automatic deceleration feature.
  • Two step programmed ejector speed for soft start ejection.
  • Digital setting of ejector speeds and positions.
  • Digital dislay of clamp, screw, and ejector position.
  • Monitoring of cycle time, clamp open to close time, injection fill time, screw recovery time, screw RPM, injection start position, shift over position, minimum cushion, and final cushion.
  • Mold separation monitor.
  • Automatic setting of deviation band for above monitored items with alarm function if any monitored item goes outside its allowable tolerance.
  • Table display and trend display of monitored data plus SPC.
  • Internal storage of all data for 30 mold set-ups.
  • Stop history, change history, and alarm history display.
  • CARLOADER built in for additional 30 molds.
  • Production completion signal with auto shut-down control.
  • Digital setting of barrel temperature with set point and actual display.
  • Reduced temperature holding program.
  • Feed forward barrel temperature program
  • High barrel temperature alarm.
  • High oil temperature alarm with auto shutdown.
  • Edit function during machine run.
  • MOLDLYZER injection profile monitor with graphics.
  • Toshiba high perfomance DBG screw for high quality melt.
  • Sprue break (after cure time, screw recovery, or injection).
  • Screw cold start protection.
  • Eject on the fly with separate pump.
  • Moveable platen supported on machine base for precision alignment of clamp during mold close.
  • Automatic grease lubrication of platen bushings and support shoes.
  • Cycle counter showing number of good, reject and total cycles.
  • Automatic oil temperature control value.
  • Ejector forward hold circuit - gate controlled in semi-auto.
  • Binary pump configuration to align energy use with production requirements.
  • Cartridge valve hydraulics.
  • Hydraulic oil warm-up circuit for quick startup with stable oil temperature.
  • Continuous oil filtration to 3 micron to reduce hydraulic component wear.
  • Robot interlock circuit.
  • Top of stationary platen pre-drilled for mounting robot.
  • LED's on control panel showing limit switch condition.
  • Digital display of feed throat temperature.
  • Pre-wired for 460/3/60 power.
  • Bimetallic barrel - nickel/boron alloy.
  • Stainless steel hopper.
  • Automatic adjusting clamp pressure switch.
  • Ejector plate holes through drilled for pull back rods.
  • Preventative mainenance schedule with alarm.
  • Try again circuit for continuous automatic operation.
  • Mercury heater contractors for low maintenance.
  • Power swivel of injection unit.
  • SPI ejector pattern, mold mounting holes, and nozzle.
  • Machine built to SPI-ANSI machinery safety standards.
  • Optical encoders for precision sensing of clamp and injection positions with accuracies of 0.001mm(0.00004in).